i-Pilot Link works with select Minn Kota Ultrex®, Ulterra®, Terrova and Riptide® trolling motors, ethernet‑capable Humminbird fish finders, and compatible Humminbird LakeMaster map, AutoChart Live map or AutoChart Zero Line SD card. For a full list of compatible models, visit MinnKotaMotors.com/iPilotLink.
Does Minn Kota Terrova work with Lowrance?
Yes, Minn Kota trolling motors are compatible with Lowrance devices! The best way to connect your Lowrance device to your Minn Kota trolling motor is through the Universal Sonar 2, or US2.
For the first time, anglers will have the option to select a Minn Kota Ulterra™, Terrova®, Ultrex™ or Fortrex® trolling motor with Built-In MEGA Down Imaging sonar. The Humminbird MEGA Down Imaging transducer will now be integrated into the trolling motor to provide a clean set up at the bow for anglers.
What fish finders are compatible with Minn Kota Terrova I pilot? – Related Questions
How do you mount a Garmin transducer on Minn Kota Terrova?
Is Garmin compatible with Minn Kota?
Minn Kota offers some trolling motors with a transducer built-in. These transducers operate at 83kHz and 200kHz. A few select Garmin devices can utilize these frequencies to connect these transducers to Garmin devices, use a Minn Kota adapter cable.
Does my Terrova have Down Imaging?
Built in MEGA DOWN Imaging is currently available on select Ultrex, Terrova, Ulterra, and Fortrex motors.
Does Terrova have sonar?
Yes, the Terrova gives customers the option to purchase the trolling motor with the Universal Sonar 2 or the MEGA Down Imaging.
Can you put a 3 in 1 transducer on trolling motor?
Trolling Motor Transducer Mount for Lowrance Transducers
Fits most Minn Kota and Motorguide trolling motors. Will work with Lowrance Total Scan, 3 in 1, and 3D transducers.
What is a US2 transducer?
Universal Sonar 2 Temperature Sensing
The US2 transducer has an array of built-in temperature sensors that will display water temperature on most major fishfinder brands that have this feature. Please refer to our US2 Compatibility Chart for specific models.
What does us2 mean on Minn Kota trolling motor?
A Universal Sonar 2 adapter plug will allow you to quickly and conveniently connect and disconnect your motor from your fish finder. Shielded cable connections virtually eliminate the possibility of sonar interference and are waterproof for extra dependability.
One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal. If the transducer is installed higher than the bottom of the boat, turbulence will roll off the edge of the boat bottom and cause interference.
Can you run 2 fish finders off 1 transducer?
Any time you run two units with the same frequency there is a risk of interference. However, with the modern noise rejection systems built into today’s fish finders, in most conditions when there is a unit on the front and back of the boat with the same frequencies, they will not interfere with each other.
Does it hurt the transducer to be out of water?
Without the water, the transducer could burn out and have issues if left running for an extended period of time out of the water.
Does it matter which side of boat you mount a transducer?
The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
How far down do you mount the transducer?
You should mount your transom-mount transducer parallel to the waterline. While the vessel is moving, the device should extend into the water 3.5 mm (0.125 in.)below a fiberglass hull or 10 mm (0.375 in.)
What happens if transducer is mounted too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer.