Smaller aluminum fishing boats typically weigh around 400 pounds and a 14 feet cabin cruisers will often weigh around 14,000 pounds.
Typical horsepower for a 14-foot jon boat would be between 15 HP and 20 HP although up to 25 HP is not uncommon either. 20 HP can comfortably give you a top speed of 20mph, potentially even stretching to 25mph depending on weather conditions and the weight on the boat.
Are aluminum boats worth it?
In addition to low-cost fixes, aluminum boat damage is fairly easy for professionals to repair. It holds its value: Because aluminum boats have a long life, they do a good job at holding their value. This means your boat’s resale value is likely to be close to what you initially paid for it.
The max rated horsepower for most 14′ boats is 15hp unless they are the wider ones. I have a 1452 with a 25 that is great. Also have a 1436 that does well with an 8hp but rated up to an 15 and would be very dangerous with a 25.
How much does a 14 foot aluminum boat weigh? – Related Questions
15 to 25 HP engine
They are an excellent choice for: 10 to 14 feet (3 – 4.5 m) long inflatable boat. 12 to 16 feet (3.65 – 5 m) long Jon boat, fiberglass boat, and aluminum fishing boat.
You should hit 20-25 MPH. It hit 20 with an aluminum 14′ with a Yamaha 9.9, 6 gallon tank, and group 29 battery.
How much hp does a 14ft boat need?
Some 14’s are wide and deep and could handle a 25 while others are narrow and shallow and would be scary at any higher speed or even sitting still with all that weight. A 15 hp is a good compromise, same weight as a 9.9 and enough speed.
How do you calculate maximum horsepower for a boat?
You multiply your boat length by the transom width. Then you take that number, which is known as the “factor,” and match it to a horsepower capacity according to the Code of Federal Regulations Table 183.53 — Outboard Boat Horsepower Capacity, shown below.
An aluminum boat that is 16 feet long needs to have a 60 horsepower motor. Once equipped, it can have a speed of 25 to 30 miles per hour.
There is a relatively simple calculation based on the length and transom width of the boat. I found it in 33 CFR 183.53. Length in feet times transom width in feet then check the table and using some common dimensions for 12′ semi v hulls the answer is about 15 hp.
How much weight can you put in a 12 ft aluminum boat?
An average 12 feet (3.65 m) long Jon boat weighs 120 pounds (54.5 kg), excluding an engine. It can hold about 400 to 450 pounds (181.5 – 204 kg) of extra load. Thanks to a maximum of 5 to 7 HP, this vessel has a top speed of 10 to 15 mph (16 – 24 km/h).
How big of a boat will a 9.9 push?
To answer the question posted “Best size aluminum boat for 9.9hp 2-stroke?” A 12ft would provide the best performance with a 9.9. If you want more boat space then a 14ft would be better but would perform best with a larger motor.
What’s better long shaft or short shaft outboard?
If it measures 15″ or with in a inch of that you will need a short shaft outboard. If it measures anywhere from 17″ to around 22″, then your going to want to go with a long shaft motor. Anything bigger than that your obviously going to need an extra long shaft.
How far below the transom should the prop be?
The outboard anti-ventilation plate should sit about 1 inch below the bottom of the boat (hull) at the transom.
How low should my outboard sit in the water?
Just low enough so that all the water intake ports are submerged, especially when the boat is cruising on a “plane”. Just low enough so that the transom does not block any water flow to the propellor.
What happens if you put a short shaft motor on a long shaft boat?
If you mount a shortshaft engine on a longshaft transom, the propeller would barely be in the water and the engine would overheat, due to the fact that the water pickup would not be submerged.
How do you raise the transom on an aluminum boat?
One non-invasive way of raising the transom on an aluminum boat is to create a “lift” — a bracket that fits over the transom — to increase the motor’s height. The completed bracket forms a channel, and the top of the channel holds the top of the outboard bracket a few inches above the transom of the boat.
What does a jack plate do on a jon boat?
Jack plates perform two key functions. One is setback, which distances an outboard from the boat’s transom, allowing the propeller to run in less-turbulent water. Jack plates also move an outboard up and down to optimize performance and enable a boat to venture into shallower water than it might otherwise.
Will short shaft motor work 20 inch transom?
It will push you forward, at low speeds, but in reverse, it is as effective as an egg beater. I have a Yamaha 15″(short) shaft F8 on my ProV(20″ transom). All I use it for is forward trolling. It works great, have never had any problems at any speed.
Can you put a long shaft outboard on a short transom?
RE:Long shaft, short transom
Yes, you can build it up, and that would work fine.