A blog about boats, fishing, water sports and having fun on the ocean
Is it hard to install a fish finder?
by
Installing a fish finder is a manageable DIY job as long as you have a little know-how and some essential tools. And even if you’re not up for the job, knowing what a proper installation looks like allows you to assess and troubleshoot your setup.
The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
How do you mount a fishfinder on a boat?
Should a fish finder be wired directly to the battery?
Wire the fish finder direct to the battery (either the cranking battery or an auxiliary battery). Don’t take shortcuts and run the fish finder power wire into a block or switch panel. Wire your fish finder the right way and extend the Humminbird power wire directly to the battery using the correct type and gauge wire.
Is it hard to install a fish finder? – Related Questions
How long does a 12V battery last on a fish finder?
with most fish finders using about 2amps, you could run it for 50 hours. most trolling motors use about 1amp per pound of thrust at full power. so if you had a 50 pound thrust motor running on high for two hours, your battery would be dead. never drain a battery below 80 to 50% and recharge right away.
How long will a battery run a fish finder?
The fish finder battery time is dependent on the size of the battery you’re using. But, generally, a normal-sized lithium-ion 12 Ah battery can run a fish finder for up to 20-24 hours.
Which battery should fish finder be connected to?
Usually, fish finders will take 12V lead-acid or lithium batteries.
Can I connect fish finder to trolling motor battery?
Sonar/finders are hyper sensitive to voltage drops and go whacky. Trolling motor batteries get too much drawdown during the day. The BEST is to have a totally separate battery for electronics.
How do you power a fishfinder at home?
Is it OK to run transducer wire next to other power wires?
Transducer cables should be run separately, not bundled together with other wiring or run close to the engine. This can cause noise-generated marks on the fish finder.
Does direction of transducer matter?
So the short answer is that no, it doesn’t matter which way you face the “front” of your transducer.. the read out is going to look just the same to you. You do, however, want the BOTTOM of your transducer to face as straight down as you can, within reason.
You can run multiple wires together. You just need to make sure they are the same gauge and voltage.
Can 2 wires go through the same hole?
The Answer
According to the National Electrical Code, you can have 4 12/2 nonmetallic sheathed cables through a single bored hole that is fire- or draft-stopped using thermal insulation, caulk, or sealing foam, or where proper spacing is not maintained for more that 24 in.
What happens if you touch 2 live wires?
If you touch both cables at the same time, then your body becomes a conductor and the current of electricity will pass through your body. Also, if you touch a cable that has current flow and also touch an electric connection that is grounded, then you become the easiest path for electricity to go to the ground.
Is it OK to put 2 ground wires together?
No.Connect only one ground wire per ground screw.
What happens when 2 wires touch each other?
If two phase wires touch each other it is considered as a fault, the great Line to Line fault . This causes huge current to flow. If the circuit breaker is operative it will trip if it doesn’t there will be huge heat causing fire or melting of the wire.
What happens if you connect live and neutral together?
When live wire comes in contact with the neutral wire, then the insulation of wires is damaged or there is a fault in the appliance. In such a situation, the current in the circuit abruptly increases. This is known as short circuiting.
One of the easiest ways to know if a wire is live is to use a voltage checker or a current checker. These are simple devices that you can touch to any wire, and it will tell you if there is electricity running through it.
What happens if you connect line to neutral?
If you short Line to Neutral, the weakest link will be opened up. The weakest link is normally a circuit breaker or a fuse, if the electrician that wired it up was competent. If a component in the short circuit path had less of a current rating than the breaker or fuse, it will be fried.
Why can you touch the neutral wire?
Touching a neutral wire and standing on floor say bare footed, remember the voltage between them is zero(potential diff is zero) because both neutral and earth are at zero potential.