A blog about boats, fishing, water sports and having fun on the ocean
Where do you put the depth finder on a pontoon boat?
by
The best place to install the fish finder’s transducer is usually on the starboard (right) side of the pontoon boat. This is because you want to make sure that you have enough cord length to run from the transducer to the fish finder monitor on your console, which is typically to the right-hand side of the boat.
Where do you put the transducer on a pontoon boat?
Most pontoon boats have a mounting bracket mounted at the rear of the pontoon tube. This is the most common place to mount a transducer on a pontoon boat. You have to make sure your transducer mount is compatible with a flush mounting surface.
What is the easiest depth finder to use?
The world’s easiest-to-use fishfinder, HOOK² 9 TripleShot features Autotuning sonar, High CHIRP, SideScan and DownScan Imaging™ — all at a price that is easy to afford.
How should a transducer be mounted on a pontoon boat?
For most pontoon boats that have the captain’s chair on the starboard (right) side of the boat, you’ll want to place the transducer on the right side so less cord is needed. Keep in mind when placing the transducer that it’s best to place it far away from electrical interference from being too close to another wire.
Where do you put the depth finder on a pontoon boat? – Related Questions
How far below the boat should a transducer be?
The transducer should be even with the bottom of the boat or slightly below the bottom. Leading edge (the edge closest to the transom of the boat). One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal.
What happens if transducer is too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer.
Where is the best place to put a transducer on a boat?
Transducer placement should be aft and close to the centerline. It needs to be located low enough that the transducer is in the water at all times. Consider items such as the lifting strap placement into the location as well as trailer bunks and rollers if it is a trailered vessel.
How far away from motor should transducer be?
The ideal mounting location on a boat powered by an outboard or an I/O engine is about 18-24 inches starboard of the engine’s lower unit. If the boat has inboard power, mount the transducer far enough to starboard to clear any propeller turbulence.
Because the transducer can only ping in water so you do want it submerged. If it’s too deep sometimes the front face of it will create turbulence and bubbles = bad. Plus it can throw water up over your motor and inside your cowling resulting in saltwater intrusion.
Should transducer be submerged?
Note: the transducer must be submerged in water for reliable transducer detection. If a transducer is detected, the unit will enter “Start Up” or normal operation unless you choose another option.
Why is my fish finder reading wrong depth?
Problem: Incorrect Depth Readings
Verify that there are not two sounders operating close together. Inspect the transducer connectors and pins for signs of corrosion. Perform a basic cavitation check. Verify that the upper and lower depth limit settings are properly set.
How do you test depth transducer?
How do you know if you have a bad transducer?
Here are the most common types of incorrect display readings that are caused by transducer errors: Display shows surface reading, but no bottom reading. Display shows wrong depth reading. Display shows erratic readings (especially when the boat speeds up)
Is it bad to run transducer out of water?
Without the water, the transducer could burn out and have issues if left running for an extended period of time out of the water.
How do I reset my depth finder?
Pressing the “ON / OFF MODE” keypad again returns the depth sounder to normal operation.
How do you clean a transducer?
To clean the transducer, use normal synthetic soap and water. To remove marine growth, use fine-grade sandpaper or emery paper. Do not use strong solvents. Do not attempt to scrape of marine growth with sheets of metal, screwdrivers or other tools made of metal or hard plastic.
Multi-element chirp transducers generate substantial heat, and so they need to be immersed in water while operating to keep cool. This is a concern mainly for trailer boaters who might leave the sonar on after putting the boat on the trailer.
How do I keep barnacles off my transducer?
I suggest using Aurora Algex. Spray it on and let it work for about 1/2 hour. It will soften the barnacles so that they can be easily scrapped off. If the growth is heavy, you may need several applications.
How do I keep barnacles off my pontoon boat?
Take the pontoon boat out of the water. For the best results, you need to get your boat out of the water.
Loosen up the barnacles with Toon Brite (optional)